Bonfiglioli Industrial Reducer Power Transmission OEM logo
Gear reducer article header
Engineering Note

What I Learned the Hard Way About INA Bearings, Linear Guides, and Pete Jackson Gear Drives: A Purchasing FAQ

2026-11-06 · Bonfiglioli Engineering Desk

Bearing Sourcing FAQ: What I Wish Someone Had Told Me Earlier

I've been handling transmission component orders for about nine years. In that time I've personally made — and documented — seven significant mistakes, totaling roughly $14,000 in wasted budget. Now I maintain our team's pre-check list so nobody repeats them.

These are the questions I get most often from newer buyers, maintenance engineers, and OEM designers. I'm not a manufacturer's rep, and I don't sell anything. I just order a lot of bearings.

1. What is INA bearings actually known for?

INA is part of the Schaeffler Group — same corporate family as FAG and LuK. If you're specifying INA, the strength is needle roller and linear motion products. Their catalogue depth on thin-section and radial-space-constrained bearings is enormous.

But here's the thing: "good brand" isn't a spec. In my first year (2017), I ordered INA needle roller bearings for a pillow block application where a standard deep-groove ball bearing would have done the job at half the cost and double the service interval. The bearings were excellent. The application was wrong. That mistake cost us $2,800 in unnecessary premium plus a two-week lead time.

My point: INA makes the right bearing for a lot of jobs. That doesn't mean they make the right bearing for your job.

2. When should I use INA needle roller bearings — and when should I not?

Needle rollers shine when radial space is tight and you're carrying high radial loads at moderate speed. That's their physics. If your housing bore is already generous, you're paying a premium for a constraint you don't have.

A practical rule I use now: if the design has room for a ball bearing of comparable bore, start there. Needle rollers are the answer to a space problem, not a general upgrade.

This worked for us on a conveyor retrofit where the existing pillow block bore was fixed. But our shop runs mostly mid-duty equipment with predictable duty cycles. If you're dealing with shock loads, reverse rotation, or heavy contamination, the calculus changes a lot.

3. Is the INA bearings website worth using?

Honest answer: the Schaeffler medias portal is more useful than the consumer-facing site. The product catalogue and technical data sheets are what you need; the marketing pages mostly confirm that INA exists and is German, which you already knew.

For sizing and interchange work, I pull the technical PDFs directly. For pricing and availability, you call a distributor. That's been true since about 2019 and hasn't changed.

4. Roller chain sizes — where do buyers actually screw this up?

The classic error isn't picking the wrong size. It's picking the right size by the wrong number.

Roller chain numbering (ANSI #40, #50, #60, etc.) is based on pitch in eighths of an inch, but the number doesn't equal the pitch. A #50 chain has a 5/8" pitch, not 5/0 of anything. I've seen a junior buyer order #60 chain for a #50 sprocket because the drawing said "chain size: 50" and the catalogue column said "#60." Total waste: $450 and a two-day production hold.

The checklist item now is simple: confirm pitch, roller diameter, and inner width against the sprocket drawing. Three numbers. Takes ninety seconds.

5. What's the most common mistake with linear ball bearings?

Contamination. Full stop.

Linear ball bearings run on recirculating balls in a raceway, and any grit that gets in there turns the raceway into a grinding wheel. In September 2021, we installed a batch of linear guides on a machine that sat near a sandblasting station. Cheap wiper seals. Forty percent failure within four months. That was a $6,200 rework plus downtime, and the bearings themselves were fine — the environment wasn't.

If your application has airborne debris, pay for proper sealing. Or specify a different linear technology entirely. I can only speak to our shop-floor conditions — clean-room and food-grade environments have their own rules that I won't pretend to know well.

6. What happened to Pete Jackson gear drives?

Pete Jackson Gear Drives was an Australian manufacturer known for blower and supercharger drive systems. If you're searching the name, you probably have legacy equipment or an old parts list that still references them. The company ceased its original manufacturing operations some years back, and spares have become a scavenger hunt.

Practical advice: if you're maintaining a machine that originally specified Pete Jackson drives, document every gear geometry now — tooth count, module, helix angle, backlash spec — before you need to reverse-engineer a replacement. I've watched a maintenance team spend three weeks measuring a drive because nobody had the original spec sheet. It cost them a production week.

7. What bearing "common knowledge" is out of date?

The one I keep hearing: "Sealed bearings need less maintenance than open bearings, so always go sealed." That was reasonable advice when seal technology was crude. Today, seal drag and heat generation matter in high-speed applications, and modern open bearings with proper lubrication systems can outlast sealed ones in the right context.

What was best practice in 2018 is not automatically best practice in 2025. The fundamentals — load rating, speed limit, lubrication, contamination — haven't changed. The execution has.

The reverse is also true. I still see buyers dismiss traditional bearing types as "old technology" when the application genuinely calls for them. A well-specified deep-groove ball bearing is not obsolete. It's just not exciting.

8. What should I check before I place any bearing order?

Four things, in this order: load direction and magnitude, available radial space, operating speed and temperature, and contamination exposure. If any of those four is a guess, stop and get the answer.

I've caught 47 potential errors using this checklist in the past 18 months. That's the whole system. Simple, but it works — for the kind of mid-range industrial work we do.

"The bearing you order should be the bearing the application needs, not the bearing the catalogue page makes most convenient."

Application engineering note

This article is written for OEM and MRO teams comparing reducer sizing, gearbox repair service and motor integration details.

Previous: We Put 40 Bosch E-Bike Motors in Our Delivery Fleet—Here's What Service Reality Taught Me Next: Why I Stopped Treating Hydraulic and Electrical Parts as Separate Purchasing Categories

Recent engineering notes

最低报价的轴承,往往是最贵的选择

一个 350 人设备制造商采购经理的 6 年 MRO 采购复盘:为什么在工业轴承和传动件采购里,TCO(总拥有成本)才是唯一该看的决策标准,以及我踩过的三个最贵的'便宜坑'。

2026-11-17

The 7-Point Pre-Mount Checklist I Run on Every Shimano Steps Drive Unit

A field-tested checklist for OEM and shop techs integrating Shimano Steps e-bike drive systems — covering E5000 vs E6100 torque specs, servo motor controller matching, speed sensor routing, disc brake conversion kits, and the linear actuator failure mode that keeps generating warranty tickets. Two documented mistakes included.

2026-11-17